Product Categories

Contact Us

Add:North ring Road, Shenze County,Shijiazhuang City,Hebei Province ,China

Tel:+86-311-87513878

Phone:+8613933870601

Fax:+86-311-83525449

E-mail: nonghahajenny@nonghaha.net.cn

Web:www.nhhmachinery.com

News

Home > News > Content
Rotary Tiller Reduce The Operating Process
Aug 09, 2017

Rotary Tiller Reduce the operating process

The rotary tiller is a tractor that drives the rotary tiller to complete the tillage, rake, and land preparation. It can mix the vegetation and mix it into the whole tillage layer. It can also mix fertilizer, pesticide, etc. in the tillage layer The After the rotary tillage operation, the soil is smooth and the surface is smooth and the operation process is reduced, so it is widely used.

 Use before installation

1, the installation and wheeled tractor supporting the three-point hanging rotary tiller, you should first cut off the power output shaft power, remove the output shaft cover, reversing and hooking a good rotary tiller, and then with the square Universal joint into the rotary tiller drive shaft, lift the rotary tiller, hand knife axis to see whether the operation is flexible, and then set the square with the universal joint into the tractor power output shaft fixed. Installation should pay attention to: the square shaft and square sleeve fork should be in the same plane, if installed wrong, universal joints will sound, rotary tiller vibration increases, and can damage the parts. After the universal joint is installed, insert the safety pin into the groove on the spline shaft and insert it with the cotter pin.

 2, the installation and tractor supporting the rotary tiller, the tractor should be tilted forward, remove the traction box, with five studs to the rotary tiller fixed on the gearbox. Note that the two pins on the two union surfaces should be aligned to ensure proper engagement of the gears after assembly. If the gears in the gearbox of the rotary tiller gear are connected with the gears in the gearbox, they can not be hard pressed and hardened. The pulley should be tilted and the gears in the gearbox should be rotated at an angle. In addition, it should be guaranteed that the thickness of the pad at the connection to the gearbox is 0.45 to 0.55 mm, which is too thick or too thin to affect the meshing clearance of the two meshing gears. When removing the rotary tiller, use the shroud to cover the gearbox to prevent the debris from falling into the box.

1. At the beginning of the operation, the rotary tiller should be lifted, first combined with the power output shaft, the knife shaft speed to the rated speed, and then down the rotary tiller, so that the blade gradually into the required depth. It is strictly forbidden to insert the blade into the power output shaft or the sharp descending rotary tiller to avoid causing the blade to bend or break and to increase the load of the tractor.

2. In the operation, should be as low as possible slow, so that can guarantee the quality of operations, so that the soil crushed, but also reduce the wear and tear of the parts. Pay attention to listen to the rotary tiller whether there is noise or metal percussion, and observe the broken soil, till the deep situation. If there is any abnormality, it should be shut down immediately for inspection, and then the operation can be continued.

3. When the ground turns, prohibit the operation, the rotary tiller should be raised, so that the blade away from the ground, and reduce the tractor throttle, so as not to damage the blade. When lifting the rotary tiller, the inclination angle of the universal joint should be less than 30 degrees. If it is too large, it will cause the impact noise to be prematurely worn or damaged.

4. In the reverse, over the ridge and transfer the land, the rotary tiller should be raised to the highest position, and cut off the power, so as not to damage the parts. Such as the distant transfer, use a locking device to fix the rotary tiller.

5. After each shift, the rotary tiller should be serviced. Remove the soil and weeds on the blade, check the fastening of the connectors, add lubricating oil to the lubricating oil, and add butter to the joints to prevent aggravating wear.